How Snake Plant Reproduce? Insightful Facts For You! (2021)

You might only have a pot of snake plants now. But if you want more you can make your snake plant reproduce for you! You don’t need to buy any more snake plant pots if you want to manufacture a lot of them. The only thing you have to do now is replicate it. So, as we’ll describe below, you’ll need to understand how this plant reproduces.


How to Reproduce Snake Plant

The way snake plant reproduce called propagation. Snake plant propagation can be done in four ways: soil, water, division, and rhizome. You can read the explanations below to learn how to do each approach.


Snake Plant Reproduce with Soil

If you want to propagate your snake plant using this approach, you’ll need a sharp knife or scissors, a pot, and succulent soil or another suitable potting mixture. Root hormone can be made if desired, although it is not required.

So, how do you propagate a snake plant this way?

After you’ve done all of the above, you’ll need to clip the leaf closest to the soil line. Use a clean, sharp knife or scissors to do so.
The leaf must next be chopped into pieces, each of which must be a couple of inches long.

After cutting the leaf into pieces, set it aside for a few days. Allow them to enjoy themselves until they become calloused. They will be protected against bacteria from the soil that can enter the leaf and cause decay by doing so.
Don’t forget about the upper and lower parts of the leaf since you must plant the lower part, which is closest to the plant’s bottom, first. Your snake plant will not grow if you do it incorrectly.
You can dip the bottom end of the snake plant cutting in rooting hormone powder if you desire. This is, however, an optional step. So, if you don’t want to, you can skip this step.

The part of the plant next to the bottom needs to be planted in soil that drains well and contains a lot of nutrients.

The plants will start to sprout roots around a month after planting.


Snake Plant Reproduce with Water

This is the most straightforward way to propagate a snake plant. To cultivate this snake plant, you’ll need a sharp knife or scissors, water, and a jar, vase, or thick glass. Rooting hormone can be made if desired, although it is not required.

What is the best way to propagate a snake plant in water? You can do so by following the steps below.

To begin, cut the leaf you intend to propagate with a sharp knife or scissors that you have prepared ahead of time. Make sure to trim the section of the leaf closest to the soil.

If you have root hormone on hand, you can dip the sliced leaf into it. If you don’t have root hormone on hand, you can skip this step.

The following step is to immerse the bottom half of the leaf in water. Make sure there’s enough water to cover about a quarter of the leaf.

If your snake plant leaves are large, you can divide them into portions and then submerge each segment in water.

When you plant your snake plant in water, you must preserve the leaf in the same orientation as when you planted it in soil. Because the leaves of snake plants are polar, they will only produce roots if the edge of the leaf closest to the soil is submerged in water.

Make sure the leaf is kept in a warm, indirect light environment. Also, remember to replace the water in the glass, jar, or vase once a week.

Roots will emerge after around two months. You can plant it in soil once you’ve discovered roots.


Snake Plant Reproduce with Division

To grow snake plants using this approach, you’ll need succulent soil or potting mixture, newspaper or outdoor area, a clean and sharp knife, and some pots. This method of propagation is ideal for those who need extra snake plants right away.

What is the best way to propagate a snake plant using this method? You can follow the instructions below.

To begin, gently place your plant on its side. The plant should next be slid out of its pot. You’ll probably need a newspaper for this, but you can also do it outside.

You must carefully examine the roots after removing the plant from its pot. Rhizome sites must be discovered.

If your snake plant is large, you can cut it up into sections. If your snake plant is little, though, you can cut it in half.

You’ll need to chop the plant using your sharp knife. Ensure that each cutting contains at least three rhizomes and one healthy leaf. Each cutting must also have a few of roots.

If your snake plant has been divided, you must repot each individual plant into a fresh pot filled with succulent soil.

Give each pot a drink, but be careful not to over-water them.


Snake Plant Reproduce with Rhizome

What exactly is a rhizome? It’s a horizontally growing underground stem. It will produce new branches in snake plants. Newspaper, a sharp knife, pots, and potting mixture or succulent soil are all required for this procedure.

How can you grow a snake plant from a rhizome? These guidelines will assist you.

Your snake plant must be turned over. After that, slide your snake plant out of the pot.

Locate some rhizomes in the root zone, directly beneath the soil. They have a whitish stem that looks like garlic.

After that, remove the rhizome from the plant’s base with a clean knife. It’s important to ensure that the roots around the plant are not damaged during cutting.

It will now take several days for the rhizome to become callous after cutting it.

If you find that there is a callous, it is time for you to plant it in a new pot.


More Articles

https://allthingsgardener.com/how-long-does-snake-plant-take-to-grow/
https://allthingsgardener.com/how-slow-is-the-snake-plant-growth/
https://allthingsgardener.com/dry-out-overwatered-snake-plant/

Was this helpful?

Yes
No
Thanks for your feedback!